Error codes describe a service procedure that must be followed. Each event ID that requires service has an associated error code.
Error codes can be either notification type E (error) or notification type W (warning). Table 1 lists the event IDs and corresponding error codes, the notification type, and the condition of the event.
| Event ID | Notification type | Condition | Error code |
|---|---|---|---|
| 009020 | E | A system recovery has run. All configuration commands are blocked. | 1001 |
| 009040 | E | The error event log is full. | 1002 |
| 009052 | W | The following causes are possible:
|
1196 |
| 009053 | E | A node has been missing for 30 minutes. | 1195 |
| 009054 | E | Node has been shut down. | 1707 |
| 009100 | W | The software install process has failed. | 2010 |
| 009101 | W | Software install package cannot be delivered to all nodes. | 2010 |
| 009150 | W | Unable to connect to the SMTP (email) server. | 2600 |
| 009151 | W | Unable to send mail through the SMTP (email) server. | 2601 |
| 009170 | W | Remote Copy feature capacity is not set. | 3030 |
| 009171 | W | The FlashCopy feature capacity is not set. | 3031 |
| 009172 | W | The Virtualization feature has exceeded the amount that is licensed. | 3032 |
| 009173 | W | The FlashCopy feature has exceeded the amount that is licensed. | 3032 |
| 009174 | W | Remote Copy feature license limit exceeded. | 3032 |
| 009175 | W | Thin-provisioned volume usage not licensed. | 3033 |
| 009176 | W | The value set for the virtualization feature capacity is not valid. | 3029 |
| 009177 | E | A physical disk FlashCopy feature license is required. | 3035 |
| 009178 | E | A physical disk Metro Mirror and Global Mirror feature license is required. | 3036 |
| 009179 | E | A virtualization feature license is required. | 3025 |
| 009180 | E | Automatic recovery of offline node failed. | 1194 |
| 009181 | W | Unable to send email to any of the configured email servers. | 3081 |
| 009182 | W | The external virtualization feature license limit was exceeded. | 3032 |
| 009183 | W | Unable to connect to LDAP server. | 2251 |
| 009184 | W | The LDAP configuration is not valid. | 2250 |
| 009185 | E | The limit for the compression feature license was exceeded. | 3032 |
| 009186 | E | The limit for the compression feature license was exceeded. | 3032 |
| 009187 | E | Unable to connect to LDAP server that has been automatically configured. | 2256 |
| 009188 | E | Invalid LDAP configuration for automatically configured server. | 2255 |
| 009189 | W | A licensable feature's trial-timer has reached 0. The feature has now been deactivated. | 3082 |
| 009190 | W | A trial of a licensable feature will expire in 5 days. | 3083 |
| 009191 | W | A trial of a licensable feature will expire in 10 days. | 3084 |
| 009192 | W | A trial of a licensable feature will expire in 15 days. | 3085 |
| 009193 | W | A trial of a licensable feature will expire in 45 days. | 3086 |
| 009194 | W | Easy Tier feature license limit exceeded. | 3032 |
| 009195 | W | FlashCopy feature license limit exceeded. | 3032 |
| 009196 | W | External virtualization feature license limit exceeded. | 3032 |
| 009197 | W | Remote copy feature license limit exceeded. | 3032 |
| 009202 | W | System SSL certificate will expire within the next 30 days. | 3130 |
| 009203 | W | System SSL certificate has expired. | 2258 |
| 010002 | E | The node ran out of base event sources. As a result, the node has stopped and exited the system. | 2030 |
| 010003 | W | The number of device logins has reduced. | 1630 |
| 010006 | E | Access beyond end of disk, or Managed Disk missing. | 2030 |
| 010008 | E | The block size is invalid, the capacity or LUN identity has changed during the managed disk initialization. | 1660 |
| 010010 | E | The managed disk is excluded because of excessive errors. | 1310 |
| 010011 | E | The remote port is excluded for a managed disk and node. | 1220 |
| 010012 | E | The local port is excluded. | 1210 |
| 010013 | E | The login is excluded. | 1230 |
| 010014 | E | The local port is excluded. | 1211 |
| 010017 | E | A timeout has occurred as a result of excessive processing time. | 1340 |
| 010018 | E | An error recovery procedure has occurred. | 1370 |
| 010019 | E | A managed disk is reporting excessive errors. | 1310 |
| 010020 | E | The managed disk error count threshold has exceeded. | 1310 |
| 010021 | W | There are too many devices presented to the system. | 1200 |
| 010022 | W | There are too many managed disks presented to the system. | 1200 |
| 010023 | W | There are too many LUNs presented to a node. | 1200 |
| 010024 | W | There are too many drives presented to a system. | 1200 |
| 010025 | W | A disk I/O medium error has occurred. | 1320 |
| 010026 | W | A suitable MDisk or drive for use as a quorum disk was not found. | 1330 |
| 010027 | W | The quorum disk is not available. | 1335 |
| 010028 | W | A controller configuration is not supported. | 1625 |
| 010029 | E | A login transport fault has occurred. | 1360 |
| 010030 | E | A managed disk error recovery procedure (ERP)
has occurred. The node or controller reported the following:
|
1370 |
| 010031 | E | One or more MDisks on a controller are degraded. | 1623 |
| 010032 | W | The controller configuration limits failover. | 1625 |
| 010033 | E | The controller configuration uses the RDAC mode; this is not supported. | 1624 |
| 010034 | W | Persistent unsupported controller configuration. | 1695 |
| 010040 | E | The controller system device is only connected to the node through a single initiator port. | 1627 |
| 010041 | E | The controller system device is only connected to the node through a single target port. | 1627 |
| 010042 | E | The controller system device is only connected to the nodes through a single target port. | 1627 |
| 010043 | W | The controller system device is only connected to the nodes through half of the expected target ports. | 1627 |
| 010044 | E | The controller system device has disconnected all target ports to the nodes. | 1627 |
| 010050 | W | Solid state drive failed and rebuild is required. | 1201 |
| 010052 | E | Solid state drive offline as a result of a drive hardware error. | 1205 |
| 010053 | E | Solid state drive reporting PFA errors. | 1215 |
| 010054 | E | Solid state drive reporting too many errors. | 1215 |
| 010055 | W | An unrecognized SAS device. | 1665 |
| 010056 | E | SAS error counts exceeded the warning thresholds. | 1216 |
| 010057 | E | SAS errors exceeded critical thresholds. | 1216 |
| 010058 | E | The drive initialization failed because of an unknown block size or a block size that is not valid; an unknown capacity or a capacity that is not valid; or was not able to set the required mode pages. | 1661 |
| 010059 | E | Solid state drive offline due to excessive errors. | 1311 |
| 010060 | E | Solid state drive exceeded warning temperature threshold. | 1217 |
| 010061 | E | Solid state drive exceeded offline temperature threshold. | 1218 |
| 010062 | E | A drive exceeded the warning temperature threshold. | 1217 |
| 010063 | W | Drive medium error. | 1321 |
| 010066 | W | Controller indicates that it does not support descriptor sense for LUNs that are greater than 2 TBs. | 1625 |
| 010067 | W | Too many enclosures were presented to a system. | 1200 |
| 010068 | E | Format of the solid state drive is corrupted. | 1204 |
| 010069 | E | Solid state drive has incorrect block size. | 1204 |
| 010070 | W | Too many controller target ports were presented to the system. | 1200 |
| 010071 | W | Too many target ports were presented to the system from a single controller. | 1200 |
| 010072 | E | The drive is offline as a result of a drive hardware error. | 1680 |
| 010073 | E | The drive is reporting predictive failure analysis (PFA) errors. | 1680 |
| 010080 | E | The drive is reporting too many errors. | 1680 |
| 010081 | E | The drive format is corrupted. | 1206 |
| 010082 | E | The block size for the drive was incorrect. | 1206 |
| 010083 | E | The drive is offline due to excessive errors. | 1680 |
| 010084 | E | The error counts for the SAS drive exceeded the warning thresholds. | 1285 |
| 010085 | W | The SAS device was not recognized. | 1666 |
| 010086 | W | The SAS enclosure was not recognized. | 1666 |
| 010087 | W | The SAS device was not able to be identified. | 1666 |
| 010088 | E | There were excessive medium errors on the drive. | 1680 |
| 010089 | E | There were excessive overall timeout errors on the drive. | 1680 |
| 010090 | E | There were excessive times when the drive stopped. | 1680 |
| 010091 | E | A drive failed validation testing. | 1680 |
| 010092 | E | Excessive medium errors on the solid state drive. | 1215 |
| 010093 | E | Excessive overall timeout errors on the solid state drive. | 1204 |
| 010094 | E | Login excluded. | 1231 |
| 010095 | E | Drive failed. | 1687 |
| 010096 | E | The drive initialization failed because of an unknown block size or a block size that is not valid; an unknown capacity or a capacity that is not valid; or was not able to set the required mode pages. | 1680 |
| 010097 | E | A drive is reporting excessive errors. | 1685 |
| 010098 | W | There are too many drives presented to a system. | 1200 |
| 010100 | W | Incorrect connection detected to a port. | 1669 |
| 010101 | E | Too many long IOs to drive. | 1215 |
| 010102 | E | A drive is reported as continuously slow with contributory factors. | 1215 |
| 010103 | E | Too many long IOs to drive (Mercury drives). | 1215 |
| 010104 | E | A drive is reported as continuously slow with contributory factors (Mercury drives). | 1215 |
| 010106 | W | Drive reporting too many t10dif errors. | 1680 |
| 010110 | W | Drive firmware download canceled because of system changes. | 3090 |
| 010111 | W | Drive firmware download canceled because of a drive download problem. | 3090 |
| 010118 | W | Too many drives attached to the system. | 1179 |
| 010119 | W | Drive data integrity error. | 1322 |
| 010120 | W | A member drive has been forced to turn off protection information support. | 2035 |
| 010121 | E | Drive exchange required. | 1693 |
| 010123 | W | Performance of external MDisk has changed. | 2115 |
| 020001 | W | There are too many medium errors on the MDisk. | 1610 |
| 020002 | E | A storage pool is offline. | 1620 |
| 020003 | W | There are insufficient virtual extents. | 2030 |
| 020007 | E | MDisk not found in easy_tier_perf.xml file. | 2110 |
| 020008 | E | Storage optimization services disabled. | 3023 |
| 029001 | W | The MDisk has bad blocks. | 1840 |
| 029002 | W | The system failed to create a bad block because MDisk already has the maximum number of allowed bad blocks. | 1226 |
| 029003 | W | The system failed to create a bad block because the system already has the maximum number of allowed bad blocks. | 1225 |
| 030000 | W | FlashCopy prepare failed due to cache flush failure. | 1900 |
| 030010 | W | FlashCopy has been stopped due to the error indicated in the data. | 1910 |
| 030020 | W | Unrecovered FlashCopy mappings. | 1895 |
| 045001 | E | One or more power supply unit fans have failed. | 1124 |
| 045002 | E | A fan is operating outside the expected range. | 1126 |
| 045003 | E | There was a fan status communications failure. | 1126 |
| 045004 | E | The power supply unit is not installed. | 1128 |
| 045005 | W | The power supply unit has indicated an input power failure. | 1138 |
| 045006 | E | The power supply unit has indicated an output failure. | 1126 |
| 045007 | E | The power supply unit has failed. | 1124 |
| 045008 | E | Cannot communicate with the power supply unit. | 1148 |
| 045009 | E | The PSU type is not valid for this enclosure type. | 1124 |
| 045010 | E | The power supply unit type is unknown to this product. | 1124 |
| 045011 | E | PSU 11S serial number not valid. | 1124 |
| 045012 | W | The canister temperature is at the warning level. | 1098 |
| 045013 | W | The canister temperature is at the critical level. | 1095 |
| 045014 | E | A SAS cable was excluded due to internal errors. | 1260 |
| 045015 | E | A SAS cable was excluded because too many change events were caused. | 1260 |
| 045016 | E | A SAS cable was excluded. | 1255 |
| 045017 | E | A SAS cable is operating at a reduced speed. | 1260 |
| 045018 | E | A SAS cable was excluded because frames were dropped. | 1260 |
| 045019 | E | A SAS cable was excluded because the enclosure discovery timed out. | 1260 |
| 045020 | W | A SAS cable is not present. | 1265 |
| 045021 | W | A canister was removed from the system. | 1036 |
| 045022 | E | A canister has been in a degraded state for too long and cannot be recovered. | 1034 |
| 045023 | E | A canister is encountering communication problems. | 1038 |
| 045024 | E | The canister VPD is not valid. | 1032 |
| 045025 | E | The canister has experienced too many resets. | 1032 |
| 045026 | E | The drive slot is causing the network to be unstable. | 1686 |
| 045027 | E | The drive slot is not running at 6 Gbps. | 1686 |
| 045028 | E | The drive slot is dropping frames. | 1686 |
| 045029 | E | The drive is visible through only one SAS port. | 1686 |
| 045031 | E | The drive power control is not functional. | 1008 |
| 045032 | E | A drive is present in the slot but does not respond to any SCSI or SAS commands. | 1686 |
| 045033 | E | The drive slot contains a device that is not responding to queries. | 1685 |
| 045034 | E | The managed enclosure is not visible from any node canisters. | 1042 |
| 045035 | E | The electronics in the enclosure has failed. | 1694 |
| 045036 | E | The electronics in the enclosure has experienced a critical failure. | 1008 |
| 045037 | E | The SAS network has too many errors. | 1048 |
| 045038 | E | The SAS network has too many errors. | 1048 |
| 045040 | W | The firmware update for the enclosure component has failed. | 3015 |
| 045041 | W | More than one initiator port was detected on the same strand. | 1005 |
| 045042 | W | The order of the enclosures is different on each strand. | 1005 |
| 045044 | W | Multiple canisters are connected to a single canister port. | 1005 |
| 045045 | W | Canister one is connected to canister two. | 1005 |
| 045046 | W | An enclosure is connected to more than one I/O group. | 1005 |
| 045047 | W | A managed enclosure is connected to the wrong I/O group. | 1005 |
| 045048 | W | An enclosure is connected to more than one chain. | 1005 |
| 045049 | W | Too many canisters are connected to a strand. | 1005 |
| 045050 | W | The canister is connected to the wrong port. | 1005 |
| 045051 | E | A SAS cable is excluded because of single port active drives. | 1260 |
| 045052 | W | More than one canister was detected at the same hop count. | 1005 |
| 045053 | E | The node location is not able to be detected. | 1031 |
| 045054 | E | An enclosure display cannot be updated. | 1694 |
| 045055 | E | There is an enclosure battery fault. | 1118 |
| 045056 | E | An enclosure battery is missing. | 1112 |
| 045057 | E | An enclosure battery is nearing end of life. | 1114 |
| 045058 | E | An enclosure battery is at end of life. | 1113 |
| 045060 | E | Drive slot cannot be excluded. | 1048 |
| 045062 | W | An enclosure battery conditioning is required but not possible. | 1131 |
| 045063 | E | There was an enclosure battery communications error. | 1116 |
| 045064 | W | A SAS port is active, but no enclosures can be detected. | 1005 |
| 045065 | E | There is a connectivity problem between a canister and an enclosure. | 1036 |
| 045066 | E | The FRU identity of the enclosure is not valid. | 1008 |
| 045067 | W | A new enclosure FRU was detected and needs to be configured. | 1041 |
| 045068 | E | The internal device on a node canister was excluded because of too many change events. | 1034 |
| 045069 | E | The internal connector on the node canister was excluded as the cause of single ported drives. | 1034 |
| 045070 | W | The canister temperature sensor cannot be read. | 1034 |
| 045071 | W | The enclosure contains both a node canister and an expansion canister. | 1037 |
| 045072 | E | The discovery failed to complete. | 1048 |
| 045073 | E | The VPD for the enclosure cannot be read. | 1048 |
| 045074 | W | The PSU temperature is at the warning level. | 1098 |
| 045075 | W | The PSU temperature is at the critical level. | 1095 |
| 045076 | E | Error reading PSU temperature sensor. | 1124 |
| 045077 | E | Attempts to exclude connector have failed. | 1260 |
| 045080 | E | There are too many self-initiated resets on the enclosure. | 1048 |
| 045081 | E | The PSU has attempted too many internal recovery actions. | 1124 |
| 045082 | E | The slots are powered off. | 1048 |
| 045083 | W | The enclosure configuration is not supported. | 1005 |
| 045084 | W | There are too many SDE enclosures on strand. | 1005 |
| 045085 | W | The SDE is detected in a chassis that is not valid. | 1005 |
| 045086 | E | Node canister internal connector failed because of dropped frames. | 1034 |
| 045103 | E | An attempt to automatically configure a reseated or replaced drive has failed. | 1686 |
| 050001 | W | The Metro Mirror or Global Mirror relationship cannot be recovered. | 1700 |
| 050002 | W | A Metro Mirror or Global Mirror relationship or consistency group exists within a system, but its partnership has been deleted. | 3080 |
| 050010 | W | A Global Mirror relationship has stopped because of a persistent I/O error. | 1920 |
| 050011 | W | A remote copy has stopped because of a persistent I/O error. | 1915 |
| 050020 | W | Remote Copy repationship or consistency groups lost synchronization. | 1720 |
| 050030 | W | There are too many system partnerships. The number of partnerships has been reduced. | 1710 |
| 050031 | W | There are too many system partnerships. The system has been excluded. | 1710 |
| 050040 | W | Background copy process for the remote copy was blocked. | 1960 |
| 050050 | W | The Global Mirror secondary volume is offline. The relationship has pinned hardened write data for this volume. | 1925 |
| 050060 | W | The Global Mirror secondary volume is offline due to missing I/O group partner node. The relationship has pinned hardened write data for this volume but the node containing the required data is currently offline. | 1730 |
| 050070 | W | Global Mirror performance is likely to be impacted. A large amount of pinned data for the offline volumes has reduced the resource available to the global mirror secondary disks. | 1925 |
| 050080 | W | HyperSwap® volume has lost synchronization between sites. | 1940 |
| 050081 | W | HyperSwap consistency group has lost synchronization between sites. | 1940 |
| 060001 | W | A thin-provisioned volume copy is offline because of insufficient space. | 1865 |
| 060002 | W | A thin-provisioned volume copy is offline because of corrupt metadata. | 1862 |
| 060003 | W | A thin-provisioned volume copy is offline because of a failed repair. | 1860 |
| 060004 | W | A compressed volume copy is offline because of insufficient space. | 1865 |
| 060005 | W | A compressed volume copy is offline because of corrupt metadata. | 1862 |
| 060006 | W | A compressed volume copy is offline because of a failed repair. | 1860 |
| 060007 | W | A compressed volume copy has bad blocks. | 1850 |
| 062001 | W | System is unable to mirror medium error. | 1950 |
| 062002 | W | Mirrored volume is offline because it cannot synchronize data. | 1870 |
| 062003 | W | Repair of a mirrored volume stopped because of difference. | 1600 |
| 070000 | E | Unrecognized node error. | 1083 |
| 070510 | E | Detected memory size does not match the expected memory size. | 1022 |
| 070511 | E | DIMMs are incorrectly installed. | 1009 |
| 070517 | E | The WWNN that is stored on the service controller and the WWNN that is stored on the drive do not match. | 1192 |
| 070521 | E | Unable to detect any Fibre Channel adapter. | 1016 |
| 070522 | E | The system board processor has failed. | 1020 |
| 070523 | W | The internal disk file system of the node is damaged. | 1187 |
| 070524 | E | Unable to update BIOS settings. | 1027 |
| 070525 | E | Unable to update the service processor firmware for the system board. | 1020 |
| 070528 | W | The ambient temperature is too high while the system is starting. | 1182 |
| 070536 | W | A system board device breached critical temperature threshold. | 1084 |
| 070538 | W | A PCI Riser breached critical temperature threshold. | 1085 |
| 070542 | E | A processor has failed. | 1024 |
| 070543 | E | No usable persistent data could be found on the boot drives. | 1035 |
| 070544 | E | The boot drives do not belong in this node. | 1035 |
| 070545 | E | Boot drive and system board mismatch. | 1035 |
| 070550 | E | Cannot form system due to lack of resources. | 1192 |
| 070556 | E | Duplicate WWNN detected on the SAN. | 1192 |
| 070558 | E | A node is unable to communicate with other nodes. | 1192 |
| 070562 | E | The node hardware does not meet minimum requirements. | 1183 |
| 070564 | E | Too many software failures. | 1188 |
| 070574 | E | The node software is damaged. | 1187 |
| 070576 | E | The system data cannot be read. | 1030 |
| 070578 | E | The system data was not saved when power was lost. | 1194 |
| 070580 | E | Unable to read the service controller ID. | 1044 |
| 070690 | W | Node held in service state. | 1189 |
| 070747 | W | Technician connected. | 747 |
| 071746 | W | Technician port connection is not valid. | 746 |
| 071747 | W | Technician connected. | 747 |
| 071820 | W | Node canister has the incorrect model for the enclosure. | 3020 |
| 071840 | W | Detected hardware is not a valid configuration. | 1198 |
| 071841 | W | Detected hardware needs activation. | 1199 |
| 072001 | E | System board has more or less processors detected. | 1020 |
| 072900 | E | There was a PCIe link failure between canisters. | 1006 |
| 072901 | E | The PCIe link is degraded between canisters. | 1052 |
| 072902 | E | Inter-canister PCIe link recovered. | 1006 |
| 072911 | E | The PCIe link for the CPU is degraded. | 1034 |
| 073001 | E | More or lesss Fibre Channel adapters detected. | 1010 |
| 073002 | E | Fibre Channel adapter is faulty. | 1050 |
| 073003 | W | The Fibre Channel ports are not operational. | 1060 |
| 073004 | E | Fibre Channel adapter detected PCI bus error. | 1012 |
| 073005 | E | System path has a failure. | 1550 |
| 073006 | W | The SAN is not correctly zoned. As a result, more than 512 ports on the SAN have logged into one Lenovo Storage V7000 port. | 1800 |
| 073007 | W | There are fewer Fibre Channel ports operational than are configured. | 1061 |
| 073305 | W | Fibre Channel speed has changed. | 1065 |
| 073310 | E | Duplicate Fibre Channel frame is detected. | 1203 |
| 073402 | E | The Fibre Channel adapter has a failure. | 1032 |
| 073404 | E | Fibre Channel adapter has detected PCI bus error. | 1032 |
| 073501 | E | The canister position in not correct. | 1192 |
| 073502 | E | Status cannot get status from partner because there is no enclosure identity. | 1192 |
| 073503 | E | The enclosure type is not correct. | 1192 |
| 073504 | E | The enclosure identity and partner does not match. | 1192 |
| 073505 | E | The enclosure identity and partner does not match. | 1192 |
| 073506 | E | The state and enclosure identity cannot be detected on the partner. | 1192 |
| 073507 | E | The enclosure identity and node state cannot be detected. | 1192 |
| 073508 | W | The system identity is different on the enclosure and the node. | 1023 |
| 073509 | E | The enclosure identity cannot be read. | 1036 |
| 073510 | E | Detected memory size does not match the expected memory size. | 1032 |
| 073512 | E | Enclosure VPD is inconsistent. | 1008 |
| 073522 | E | The system board service processor has failed. | 1034 |
| 073523 | W | The internal disk file system of the node is damaged. | 1187 |
| 073525 | E | Unable to update the service processor firmware of the system board. | 1034 |
| 073528 | E | Ambient temperature is too high during system startup. | 1098 |
| 073535 | E | The internal PCIe switch of the node canister failed. | 1034 |
| 073550 | E | System cannot be created because of lack of resources. | 1192 |
| 073556 | E | Duplicate WWNN are detected on the SAN. | 1133 |
| 073562 | E | The node hardware does not meet the minimum requirements. | 1034 |
| 073565 | E | The internal drive of the node is failing. | 1032 |
| 073573 | E | Node software inconsistent (not raised on this platform). | 1187 |
| 073574 | E | The system data cannot be read. | 1187 |
| 073578 | E | The system data was not saved when power was lost. | 1194 |
| 073651 | E | The canister battery is missing. | 1153 |
| 073652 | E | The canister battery has failed. | 1154 |
| 073653 | E | The canister battery's temperature is too low. | 1156 |
| 073654 | E | The canister battery's temperature is too high. | 1157 |
| 073655 | E | The canister has a battery communications fault. | 1158 |
| 073656 | E | The canister battery has insufficient charge. | 1184 |
| 073700 | E | The Fibre Channel adapter is missing. | 1045 |
| 073701 | E | The Fibre Channel adapter failed. | 1046 |
| 073702 | E | The Fibre Channel adapter has a PCI error. | 1046 |
| 073703 | E | The Fibre Channel adapter is degraded. | 1045 |
| 073704 | W | Fewer Fibre Channel ports are operational. | 1061 |
| 073705 | W | Fewer Fibre Channel I/O ports are operational. | 1450 |
| 073710 | E | The SAS adapter is missing. | 1045 |
| 073711 | E | The SAS adapter has failed. | 1046 |
| 073712 | E | The SAS adapter has a PCI error. | 1046 |
| 073713 | E | The SAS adapter is degraded. | 1046 |
| 073720 | E | The Ethernet adapter is missing. | 1045 |
| 073721 | E | The Ethernet adapter has failed. | 1046 |
| 073722 | E | Ethernet adapter PCI error. | 1046 |
| 073723 | E | Ethernet adapter degraded. | 1046 |
| 073724 | W | Fewer Ethernet ports are operational. | 1401 |
| 073730 | E | The bus adapter is missing. | 1032 |
| 073731 | E | The bus adapter has failed. | 1032 |
| 073732 | E | The bus adapter has a PCI error. | 1032 |
| 073733 | E | The bus adapter is degraded. | 1032 |
| 073734 | W | The inter-canister PCIe has a link failure. | 1006 |
| 073748 | W | Technician port remains enabled. | 748 |
| 073768 | W | Ambient temperature warning. | 1094 |
| 073769 | W | CPU temperature warning. | 1093 |
| 073840 | E | Detected hardware is not a valid configuration. | 1198 |
| 073841 | E | Detected hardware needs activation. | 1199 |
| 073860 | W | The fabric is too large. | 1800 |
| 074001 | W | System is unable to determine VPD for a FRU. | 2040 |
| 074002 | E | The node warm started after a software error. | 2030 |
| 074003 | W | A connection to a configured remote system has been lost because of a connectivity problem. | 1715 |
| 074004 | W | A connection to a configured remote system has been lost because of too many minor errors. | 1716 |
| 076001 | E | The internal disk for a node has failed. | 1030 |
| 076002 | E | The hard disk is full and cannot capture any more output. | 2030 |
| 076401 | E | One of the two power supply units in the node has failed. | 1096 |
| 076402 | E | One of the two power supply units in the node cannot be detected. | 1096 |
| 076403 | E | One of the two power supply units in the node is without power. | 1097 |
| 076502 | E | The PCIe lanes on a high-speed SAS adapter are degraded. | 1121 |
| 076503 | E | A PCI bus error occurred on a high-speed SAS adapter. | 1121 |
| 076504 | E | A high-speed SAS adapter requires a PCI bus reset. | 1122 |
| 076505 | E | The SAS adapter has an internal fault. | 1121 |
| 076511 | E | A high-speed SAS controller is missing. | 1032 |
| 076512 | E | The PCIe lanes on a high-speed SAS adapter are degraded. | 1032 |
| 076513 | E | A PCI bus error occurred on a high-speed SAS adapter. | 1032 |
| 076514 | E | A high-speed SAS adapter requires a PCI bus reset. | 1034 |
| 077001 | E | The node service processor indicated Fan 1 failure. | 1070 |
| 077002 | E | The node service processor indicated Fan 2 failure. | 1070 |
| 077003 | E | The node service processor indicated Fan 3 failure. | 1070 |
| 077004 | E | The node service processor indicated Fan 4 failure. | 1070 |
| 077005 | E | The node service processor indicated Fan 5 failure. | 1071 |
| 077011 | E | The node service processor indicated that the ambient temperature threshold was exceeded. | 1075 |
| 077012 | E | The node service processor indicated temperature warning threshold was exceeded. | 1076 |
| 077013 | E | The node service processor indicated soft or hard shutdown temperature threshold was exceeded. | 1077 |
| 077021 | E | The node service processor indicated 12-volt supply has exceeded thresholds. | 1080 |
| 077022 | E | The node service processor indicated 5-volt supply has exceeded thresholds. | 1080 |
| 077023 | E | The node service processor indicated 3.3-volt supply has exceeded thresholds. | 1080 |
| 077024 | E | The node service processor indicated 2.5-volt supply has exceeded thresholds. | 1081 |
| 077025 | E | The node service processor indicated 1.5-volt supply has exceeded thresholds. | 1081 |
| 077026 | E | The node service processor indicated 1.25-volt supply has exceeded thresholds. | 1081 |
| 077027 | E | The node service processor indicated that the CPU supply has exceeded thresholds. | 1081 |
| 079500 | W | The limit on the number of system secure shell (SSH) sessions has been reached. | 2500 |
| 079501 | W | Unable to access the Network Time Protocol (NTP) network time server. | 2700 |
| 079503 | W | Unable to connect to NTP server that has been automatically configured. | 2702 |
| 079504 | W | Hardware configurations of nodes differ in an I/O group. | 1470 |
| 081002 | E | An Ethernet port failure has occurred. | 1401 |
| 082001 | E | A server error has occurred. | 2100 |
| 082002 | W | Service failure has occured. | 2100 |
| 083001 | E | System failed to communicate with UPS. | 1145 |
| 083002 | E | UPS output loading was unexpectedly high. | 1165 |
| 083003 | E | Battery has reached end of life. | 1190 |
| 083004 | E | UPS battery has a fault. | 1180 |
| 083005 | E | UPS electronics has a fault. | 1170 |
| 083006 | E | UPS frame has a fault. | 1175 |
| 083007 | E | UPS is overcurrent. | 1160 |
| 083008 | E | UPS has a fault but no specific FRU is identified. | 1185 |
| 083009 | E | The UPS has detected an input power fault. | 1140 |
| 083010 | E | UPS has a cabling error. | 1150 |
| 083011 | E | UPS ambient temperature threshold has exceeded. | 1135 |
| 083012 | E | UPS ambient temperature is high. | 3000 |
| 083013 | E | UPS crossed-cable test is bypassed because of an internal UPS software error. | 3010 |
| 084000 | W | An array MDisk has deconfigured members and has lost redundancy. | 1689 |
| 084100 | W | An array MDisk is corrupt because of lost metadata. | 1240 |
| 084200 | W | Array MDisk has taken a spare member that does not match array goals. | 1692 |
| 084201 | W | An array has members that are located in a different I/O group. | 1688 |
| 084300 | W | An array MDisk is no longer protected by an appropriate number of suitable spares. | 1690 |
| 084301 | W | No spare protection exists for one or more array MDisks. | 1690 |
| 084302 | W | Distributed array MDisk has fewer rebuild areas available than threshold. | 1690 |
| 084500 | W | An array MDisk is offline. The metadata for the inflight writes is on a missing node. | 1243 |
| 084400 | W | A background scrub process has found an inconsistency between data and parity on the array. | 1691 |
| 084420 | w | Array MDisk has been forced to disable hardware data integrity checking on member drives. | 2035 |
| 084600 | W | An array MDisk is offline. Metadata on the missing node contains needed state information. | 1243 |
| 084700 | W | Array response time too high. | 1750 |
| 084701 | W | Distributed array MDisk member slow write count threshold exceeded. | 1750 |
| 084800 | E | Distributed array MDisk offline due to I/O timeout. | 1340 |
| 988308 | I | Distributed array MDisk rebuild started. | |
| 988309 | I | Distributed array MDisk rebuild completed. | |
| 988310 | I | Distributed array MDisk copyback started. | |
| 988311 | I | Distributed array MDisk copyback completed. | |
| 988312 | I | Distributed array MDisk initialization started. | |
| 988313 | I | Distributed array MDisk initialization completed. | |
| 988314 | I | Distributed array MDisk needs resynchronization. |