Use the chserviceip command to set the
service address for a specific node.
Syntax
satask chserviceip [ -serviceipipv4 [ -gwipv4 -maskipv4 ] ] [ -resetpassword ] [ panel_name ]
satask chserviceip [ -serviceip_6 ipv6 [ -gw_6 ipv6 -prefix_6 int ] ] [ -resetpassword ] [ panel_name ]
satask chserviceip { -default | -dhcp | -dhcp_6 } [ -resetpassword ] [ -techport { enable | disable } ] [ -force ] [ panel_name ]
Parameters
- satask
- System Administrator task; service commands that
are only used in specific circumstances.
- -default
- (Optional) Resets the Internet Protocol Version 4 (IPv4) service
address to the default address.
- panel_name
- (Optional) Specifies the node being serviced.
- -serviceip
- (Required) Specifies the IPv4 address for the service assistant.
Note: The IPv4 service address can
be unconfigured by setting the address to 0.0.0.0.
- -gw
- (Optional) Specifies the IPv4 gateway for the service
assistant. If -gw is specified, -mask must
be specified.
- -mask
- (Optional) Specifies the IPv4 subnet for the service
assistant. If -mask is specified, -gw must
be specified.
- -serviceip_6
- (Required) Specifies the Internet Protocol Version
6 (IPv6) address for the service assistant.
Note: The IPv6 service address can
be unconfigured by setting the address to 0:0:0:0:0:0:0:0.
- -gw_6
- (Optional) Specifies the IPv6 gateway for the service
assistant. If -gw_6 is specified, -prefix_6 must
be specified.
- -prefix_6
- (Optional) Specifies the IPv6 prefix for the service
assistant. If -prefix_6 is specified, -gw_6 must
be specified.
- -default
- (Optional) Resets to the default IPv4 address.
- -resetpassword
- (Optional) Sets the service assistant password to default.
- -dhcp
- (Optional) Attempts to obtain an IPv4 address from
Dynamic Host Configuration Protocol (DHCP).
- -dhcp_6
- (Optional) Attempts to obtain an IPv6 address from DHCP.
- -techportenable | disable
- (Optional) Enables or disables the technician port for a node
if emergency maintenance is required.
Important: If you
specify enable you must also specify -force.
- -force
- (Optional) Helps enable the technician port for emergency maintenance.
This parameter is required if you specify enable with -techport.
Description
This command sets the service
assistant IP address for a specific node. If the node is part of clustered system (system) then the
system gateway, subnet and prefix will be used unless specified otherwise. If the node is a
candidate node, the subnet, prefix and gateway must be specified. If you specify an IPV4 or IPV6
address, but do not provide a gateway, mask, or prefix, then the existing gateway, mask, and prefix
values are preserved.
Consequently, you can configure both an IPv4 and an IPv6 address concurrently. Setting the
IPv4 address does not change the IPv6 setting, and setting the IPv6 address will not change the IPv4
setting. It is possible to clear any values set by setting the IPv4 address to 0.0.0.0 or leaving
the IPv6 value empty.
Use the
chserviceip command to:
An invocation example
satask chserviceip
The
resulting output:
No feedback
An invocation example using specific -serviceip, -gw,
and -mask parameters
satask chserviceip -serviceip 1.2.3.4 -gw 1.2.3.1 -mask 255.255.255.0
The
resulting output:
No feedback
An invocation example enabling the technician port on a node
satask chserviceip -techport enable -force
The resulting output:
No feedback