You can replace the midplane of an enclosure that is currently
not online to a system.
To replace the enclosure midplane of a control enclosure,
start with Replacing a control enclosure midplane.
To replace the enclosure midplane hardware only, complete
the following steps.
- Disconnect all cables, labeling each cable to record exactly
which port it was attached to (so that the cables can be inserted
back into the same ports later).
- Carefully remove each hard disk drive and label it with
the drive slot from which it was removed (so that the drives can be
inserted back into the same slots later).
Refer to
Figure 1 and
Figure 2.
Figure 1. Removing a 2.5 inch drive
Figure 2. Removing a 3.5 inch drive
- Remove the two power supplies from the enclosure.
- On the canister, unlatch the release levers and pull them open (see Figure 3).
Remove the node canister from the enclosure.Figure 3. Removing a node canister
- Remove the end caps from the enclosure, as described in Replacing enclosure end caps.
- Remove the two screws that securing
the front of the enclosure into the rack.
Label these screws to indicate the location from which they
are removed and place them aside.
- Slide the enclosure from the rack cabinet, turn it on its
side with the bottom facing toward you, and place the enclosure on
a flat surface.
- Remove the four screws from the
bottom of the enclosure.
Three screws are near the front and one is near the middle (see
Figure 4). Label these screws to indicate the location from which
they are removed and place them aside.
Figure 4. Locations of screws attaching the midplane assembly to the
enclosure
- Turn the enclosure top side up and place it on a flat surface.
- Remove the three screws and one
screw-pin on the right side that secure the midplane assembly to the
enclosure.
Label the screws to indicate the location from which they are
removed and place them aside. See
Figure 4.
- Remove the three screws and one
screw-pin on the left side that secure the midplane assembly to the
enclosure.
Label the screws to indicate the location from which they are
removed and place them aside. See
Figure 4.
- Remove the midplane assembly from the chassis by rotating
the midplane assembly up about 45° and then lifting it out (Figure 5).
Set the midplane assembly on a flat surface.
Figure 5. Removing the enclosure midplane assembly
- Remove the six screws that attach
the midplane to the rear of the midplane assembly and lift off the
failed midplane (Figure 6).
Figure 6. Removing the enclosure midplane from the midplane assembly
- Unpack the replacement midplane and align the six screw
holes on the midplane with the six screw holes on the midplane assembly.
Secure the midplane to the midplane assembly with the six screws
that you removed in step
13. Insert the three tabs on the midplane assembly into the
tab holes in the enclosure and rotate the front of the assembly down.
- Grasp the midplane assembly with two hands and hold it
at a 45° angle (Figure 7).
Figure 7. Aligning the midplane assembly in the enclosure
- Insert the three tabs on the midplane assembly into the
tab holes in the enclosure and rotate the front of the assembly down.
- Secure the midplane assembly to the chassis on both the
right and left sides of the enclosure by using the six screws and
two screw-pins that you removed in steps 10 and 11.
- Turn the enclosure on its side with the bottom facing toward
you and insert the four screws on the bottom of the enclosure by using
the screws that you removed in step 8.
- Reinstall the enclosure in the rack cabinet, securing it
with the two screws removed at step 6.
- Reinstall the end caps at the front of the enclosure, as
described in Replacing enclosure end caps.
- Reinstall the hard disk drives at the front of the enclosure,
making sure that each drive is inserted back in the same slot from
which it was removed.
- Reinstall the canisters into the same slots they were removed
from.
- Reinstall the two power supplies.
- Reconnect the data cables at the rear of the enclosure.