Replacing an adapter - Lenovo Storage DX8200

Use this section to replace an adapter in a riser-card assembly.

The following illustration shows the locations of the adapter expansion slots from the rear of the server.

Figure 1. PCI riser-card adapter expansion slot locations

Figure 2. PCI riser-card adapter expansion slot locations

Figure 3. PCI riser-card adapter expansion slot locations

The following table describes the maximal card dimension supported in each slot.

Table 1. The maximal card dimension supported in each slot.
Riser-card assembly	Slot number	The maximal card dimension supported
Riser-card assembly 1	1	Full height, up to full length
	2	Full height, up to full length
	3	Full height, half length
	4	Low-profile
	5	Low-profile
Riser-card assembly 2	6	Full height, up to full length
	7	Full height, up to full length
	8	Full height, half length

The following notes describe the types of adapters that the server supports and other information that you must consider when you install an adapter:

Locate the documentation that comes with the adapter and follow those instructions in addition to the instructions in this section.
The server provides two internal SAS connectors and two SAS/SATA RAID riser-card slots on the system board. See System-board optional-device connectors for the location of the internal SAS/SATA RAID connector and riser-card slots. You can replace the ServeRAID SAS/SATA adapter with an optional ServeRAID SAS/SATA adapter in the slot. For configuration information, see the ServeRAID documentation at the Lenovo Support Portal.
Do not set the maximum digital video adapter resolution above 1600 x 1200 at 75 Hz for an LCD monitor. This is the highest resolution that is supported for any add-on video adapter that you install in the server.

Read the following table before installing memory modules when any NVIDIA adapters is installed.

Table 2. NVIDIA video adapter configurations.
Description	Supported maximum total memory size
NVIDIA Grid K1 and K2	1 TB
NVIDIA Tesla K8, K40c, and M60 (Active)	1 TB
NVIDIA Quadro K420, K620, K2200, K4200, K5200, K6000, and M5000	1 TB

Do not install the following adapters in the slot 1.

Table 3. Non-supported adapters in the slot 1.
Adapter description	Option part number	FRU part number
Emulex 16Gb FC Single-port HBA for Lenovo System x	81Y1655	00D8546
Emulex 16Gb FC Dual-port HBA for Lenovo System x	81Y1662	00JY849

Do not install the following adapters in the slot 3 and the slot 8.

Table 4. Non-supported adapters in the slot 3 and the slot 8.
Adapter description	Option part number	FRU part number
N2215 SAS/SATA HBA for System x	47C8675	47C8676
N2215 SAS/SATA HBA for System x	00AE912	00AE914
ServeRAID M5225-2GB SAS/SATA Controller for System x	00AE938	00AE939
Emulex Dual Port 10GbE SFP+ VFA IIIr for System x	00D8540	00D8543
Mellanox ConnectX-3 40GbE/ FOR IB VPI Adapter for System x	00D9550	00D9552
Broadcom NetXtreme 2x10GbE Base T Adapter for System x	44T1370	00E2714
Qlogic 8200 Dual PORT 10GbE SFP+ Adapter for System x	90Y4600	90Y4605
Broadcom NetXtrme Dual Port 10GbE SPG+ Adapter for System x	94Y5180	94Y5182
Mellanox ConnectX-3 10GbE Adapter for System x	00D9690	00D9692
Intel x520 Dual Port 10GbE SFP+ Adapter for System x	49Y7960	49Y7962
Emulex VFA5 2x10GbE SFP+ Adapter for System x	00JY830	00JY833

Any high-definition video-out connector or stereo connector on any add-on video adapter is not supported.
When you install any PCI adapter, the power cords must be disconnected from the power source before you remove the PCI Express riser-card assembly. Otherwise, the active power management event signal will be disabled by the system-board logic, and the Wake on LAN feature might not work. However, after the server is powered-on locally, the active power manager active power management event signal will be enabled by the system-board logic.
When you install an Intel X540 ML2 Dual Port 10GbaseT Adapter (Option part number is 00D1994), you need to install the PCIe Thermal Solution Kit (Option part number: 00MU908) first to avoid the potential thermal issue.
Support Intel MIC GPU cards (3120A and 7120A) up to 35C/3000ft, otherwise GPU card performance could be downgraded.

Attention:

Do not install over 3 ServeRAID M1215 SAS/SATA controllers in one system.
Do not install the NVIDIA Grid Kx/Mxx, the NVIDIA Quadro Kxxxx or the NVIDIA Tesla Kxx adapter options in systems containing 1 TB of system memory or more. If these options are installed in systems with 1 TB of memory or more, it might cause undetected data corruption and system instability. These options are only supported in systems containing less than 1 TB of memory. For more information, go to https://support.lenovo.com/us/en/documents/migr-5096047.

To replace an adapter, complete the following steps:

Read the safety information that begins on Safety and Installation guidelines.
Turn off the server and peripheral devices and disconnect the power cords and all external cables.
Remove the server top cover (see Removing the top cover).
Determine which expansion slot you will use for the adapter. If you are installing an adapter in PCI expansion slot 1, 2, or 3, remove riser-card assembly 1; if you are installing an adapter in expansion slot 6, 7, or 8, remove riser-card assembly 2. See Removing a riser-card assembly
1 Slide the retention bracket; then, 2 rotate it to the open position.
Slide the expansion-slot cover out of the riser-card assembly expansion slot.
Align the adapter with the PCI connector on the riser card and press the adapter firmly into the PCI connector on the riser card.
Figure 4. Adapter installation
Rotate the retention latch to the close position.
Note: Fasten the screw on the retention latch to secure the adapter.
If you are installing a full-height, full-length adapter, insert the shipping brackets.
Figure 5. Full-height, full-length adapter
Connect any required cables to the adapter.
Attention:
- When you route cables, do not block any connectors or the ventilated space around any of the fans.
- Make sure that cables are not routed on top of components that are under the riser-card assembly.
- Make sure that cables are not pinched by the server components.
Align the riser-card assembly with the selected PCI connector on the system board and align it with the slots on the chassis; then, lower it into the server and press down firmly until the riser-card assembly is seated correctly in the connector on the system board.
- For half-length and low profile adapters
  Figure 6. Riser-card assembly installation - half-length and low profile adapters
- For full-height, full-length adapters
  Note: Shipping brackets are only included in the server that is pre-configured with full-height, full-length adapters
  
  Figure 7. Riser-card assembly installation - full-height, full-length adapters
Perform any configuration tasks that are required for the adapter.
Reinstall the top cover (see Replacing the top cover).
Slide the server into the rack.
Reconnect the power cords and any cables that you removed.
Turn on the peripheral devices and the server.

Replacing an adapter in a riser-card assembly