You can use the chnodecanister command
to change the name that is assigned to a node and other options. The
name can then be used when running subsequent commands. All the
parameters that are associated with this command are optional. However,
you must specify one or more parameters with this command.
Syntax
chnodecanister { [ -iscsialiasalias ] | -noiscsialias } [ -failover ] [ -namenew_node_name ] [ -identify { yes | no } ] [ { [ -site { site_id | site_name } ] | [ -nosite ] } ] { object_id | object_name }
Parameters
- -iscsialiasalias
- (Optional) Specifies the iSCSI name of the node. The maximum length
is 79 characters.
- -noiscsialias
- (Optional) Clears any previously set iSCSI name for this node.
This parameter cannot be specified with the iscsialias parameter.
- -failover
- (Optional) Specifies that the name or iSCSI alias being set is
the name or alias of the partner node in the I/O group. When there
is no partner node, the values set are applied to the partner node
when it is added to the clustered system (system). If this parameter
is used when there is a partner node, the name or alias of that node
changes.
- -namenew_nodecanister_name
- (Optional) Specifies the name to assign to the node canister.
Note: Node
canister names supplied with -name on chnodecanister commands
must not be in use already as node canister names or as node canister
failover names.
Important: The
iSCSI Qualified Name (IQN) for each node canister is generated using
the system and node canister names. If you are using the iSCSI protocol,
changing either name also changes the IQN of all of the node canisters
in the system and might require reconfiguration of all iSCSI-attached
hosts.
- -identifyyes | no
- (Optional) Allows you to control the light-emitting
diode (LED) used on the node. The values are yes or no.
- -sitesite_id | site_name
- (Optional) Specifies the numeric site value or site name for the
existing node. The value for site_id is 1 or 2.
The value for site_name is an alphanumeric string.
Note: If
the system topology is hyperswap, the site assigned
to a node cannot be changed.
- -nosite
- (Optional) Resets the site value.
- object_id | object_name
- (Required) Specifies the object name or ID that you want to modify.
The variable that follows the parameter is either:
- The object name that you assigned when you added the node canister
to the system
- The object ID that is assigned to the node canister (not the worldwide
node name)
Description
If the failover parameter
is not specified, this command changes the name or iSCSI alias of
the node canister. You can then use the name to identify the node
canister in subsequent commands.
The failover parameter
is used to specify values that are normally applied to the partner
node in the I/O group. When the partner node is offline, the iSCSI
alias and IQN are assigned to the remaining node canister in the I/O
Group. The iSCSI host data access is then preserved. If the partner
node is offline when these parameters are set, the node canister they
are set on handles iSCSI I/O requests to the iSCSI alias specified,
or the IQN that is created using the node canister name. If the partner
node canister in the I/O group is online when these parameters are
set, the partner node canister handles iSCSI requests to the iSCSI
alias specified, and its node canister name and IQN change.
To change the name of the node (with I/O running)
:
- Make sure the host system has active sessions with both node canisters
in the I/O group (hosting the volume on which the I/O occurs).
- Change name of one node canister using chnode command.
- From the host system, log out of the node canister whose name
changes.
- Rediscover the target iSCSI qualified name (IQN) from the host
using the host operating system's discovery mechanism.
- Login with the new target IQN discovered on the host system, and
make sure the login succeeds.
- Repeat steps 2-5 with the other node canister.
Note: When using VMware ESX, delete the static paths (in the
iSCSI initiator properties) that contain the old target IQN.
This
ensures that the node canister name change does not impact iSCSI I/O
during events such as a target failover.
An invocation example
chnode -name newname -identify yes node8
The
resulting output:
No feedback
An invocation example
chnodecanister -name testnodeone nodeone
The resulting output:
No feedback
An invocation example
chnode -site 1 node2
The
resulting output:
No feedback