lsenclosurebattery

Use the lsenclosurebattery command to display information about the batteries. The batteries are located in the node canisters.

Syntax

lsenclosurebattery [ -nohdr ] [ -filtervalueattribute_value ] [ -filtervalue? ] [ -delimdelimiter ] [ [ -batterybattery_id ] enclosure_id ]

Parameters

-nohdr

(Optional) By default, headings are displayed for each column of data in a concise style view, and for each item of data in a detailed style view. The -nohdr parameter suppresses the display of these headings.

Note: If there is no data to be displayed, headings are not displayed.

-filtervalueattribute=value

(Optional) Specifies a list of one or more filters. Only objects with a value that matches the filter attribute value are returned. If a capacity is specified, the units must also be included.

Note: Some filters allow the use of a wildcard when you enter the command. The following rules apply to the use of wildcards when you use the CLI:

The wildcard character is an asterisk (*).
The command can contain a maximum of one wildcard.
When you use a wildcard, you must enclose the filter entry within double quotation marks (""), as follows:
```
lsenclosurebattery -filtervalue "battery_id=1"
```

-filtervalue?

(Optional) Displays a list of valid filter attributes for the -filtervalueattribute=value parameter:

battery_id
charging_status
enclosure_id
end_of_life_warning
percent_charged
recondition_needed
status

-delimdelimiter

(Optional) By default in a concise view, all columns of data are space-separated. The width of each column is set to the maximum width of each item of data. A detailed view provides each item of data in its own row, and if the headers are displayed, the data is separated from the header by a space. The -delim parameter overrides this behavior. Valid input for the -delim parameter is a 1-byte character. If you enter -delim : on the command line, the colon character (:) separates all items of data in a concise view; for example, the spacing of columns does not occur. In a detailed view, the data is separated from its header by the specified delimiter.

-batterybattery_id

(Optional) Provides a detailed view of the specified battery. Valid only when an enclosure is specified.

enclosure_id

(Optional) Lists the batteries for the specified enclosure.

Description

This command displays information about the batteries, which are located in the node canisters. The concise view displays a line for each battery slot in every enclosure whether a battery exists for that slot or not. Batteries are not shown for expansion enclosures.

This table shows possible outputs.

Table 1. lsenclosurebattery outputs
Attribute	Description
enclosure_id	Identifies the identity of the enclosure that contains the battery.
battery_id	Identifies the battery in the enclosure.
status	Identifies the status of the battery: `online` indicates that the battery is present and working as usual. `degraded` indicates that the battery is present but not working as usual. `offline` indicates that the battery cannot be detected.
percent_charged	Indicates the charge of battery (in a percentage).
end_of_life_warning	Identifies the battery's end of life (with a warning noise). The values are `yes` and `no`. Important: Replace the battery.
FRU_part_number	Identifies the FRU part number of the battery.
FRU_identity	Identifies the 11S number, combining the manufacturing part number and the serial number.
firmware_level	The version of the microcode image that is installed on the battery.
error_sequence_number	Indicates the error log (or event log) number of the highest priority error for this object. This output field is typically blank. However, if there is a problem (for example, the status is `degraded`), then it contains the sequence number of that error event.
remaining_charge_capacity_mAh	Identifies the battery's remaining charge capacity in milliampere-hour (mAh).
full_charge_capacity_mAh	Identifies the fully charged capacity of the battery in mAh (this value diminishes as the battery ages).
compatibility_level	Identifies the battery driver software must support this level to operate with this battery - this value comes from the battery vital product data (VPD).
last_recondition_timestamp	Identifies a system timestamp, in the format `YYMMDDHHMMSS`, for when the last successful calibration of the gas gauge occurred, where: `Y` is year (The first) `M` is month `D` is day `H` is hour (The second) `M` is minute `S` is second
powered_on_hours	Identifies the number of hours the battery is in a powered node (not necessarily the same node).
cycle_count	Identifies the number of charge or discharge cycles that are performed on the battery.

A concise invocation example

lsenclosurebattery 1

The resulting output:

enclosure_id battery_id status charging_status recondition_needed percent_charged end_of_life_warning 
1            1          online idle            no                 100             no                  
1            2          online idle            no                 100             no

A detailed invocation example

lsenclosurebattery -battery 1 1

The resulting output:

enclosure_id 1
battery_id 1
status online
charging_status idle
recondition_needed no
percent_charged 100
end_of_life_warning no
FRU_part_number 31P1807
FRU_identity 11S00AR085YM30BG42R04P
firmware_level 105:1
error_sequence_number 
remaining_charge_capacity_mAh 3477
full_charge_capacity_mAh 3795
compatibility_level 1
last_recondition_timestamp 140528045617
powered_on_hours 1162
cycle_count 10