Migrating data by using Fibre Channel connections

You can use Fibre Channel (FC) or Fibre Channel over Ethernet (FCoE) connections to migrate data from a Lenovo V series family system to a Lenovo Storage V series system.

Install and configure the systems.
Lenovo Storage V series supports FC and FCoE connections to migrate data from the following Lenovo V series family systems:
- IBM Storwize^® V3500 for Lenovo
- IBM Storwize^® V3700 for Lenovo
- IBM Storwize^® V7000 for Lenovo, Storwize^® V7000 Gen2, and Storwize V7000 Gen2+
- Lenovo Storage V series
Ensure that all systems are running a level of software that enable them to recognize the other nodes in the cluster. For example, software level 7.7.1 is required to support and recognize nodes.
Ensure that all systems are running a level of software that can support the type of Fibre Channel adapters that are being used.
As an example, software level 7.6.0.3 or higher is required to support and recognize systems that have a 4-port 16 Gbps Fibre Channel adapter installed.
Ensure that the systems use Fibre Channel adapters at the same speed. To avoid performance bottlenecks, do not use a combination of 8 Gbps and 16 Gbps links.
Verify that the host attachment ports are available.
Ensure that you have the appropriate number of cables to connect to each system or switch, as needed.
Stop all host I/O operations.
Unmap the logical drives that contain the data from the hosts.
Verify that the Lenovo Storage V series system is configured as a replication layer system. To do so, enter the following command.
```
svcinfo lssystem
```
If the Lenovo Storage V series system is not configured as a replication layer system, enter the following command.
```
svctask chsystem -layer replication
```
Verify that the Lenovo V series family system is configured as a storage layer system. To do so, enter the following command.
```
svcinfo lssystem
```
If the Lenovo V series family system is not configured as a storage layer system, enter the following command.
```
svctask chsystem -layer storage
```

Hardware configuration

Unplug the FC cables between the Lenovo V series family system and the hosts.
Ensure that no host ports on the Lenovo Storage V series system are occupied.
Connect four FC host ports on the Lenovo V series family system to the FC host ports on the Lenovo Storage V series system.
The cabling for the port connections can vary, depending on whether the systems are connected directly or though a switch. To provide extra redundancy and ensure that the detected MDisks are not degraded, ensure that each controller is connected to both node canisters or switches, if applicable.

Figure 1 shows Fibre Channel connections that use direct cabling between the systems. To enable migration, a 4-port FC host interface adapter is installed on both systems. Any two ports on the host interface adapter can be used. In this example, ports 1 and 2 are used. In this example, data is being migrated from a Lenovo Storage V series system to a Lenovo Storage V5030 system.

Figure 1. Direct Fibre Channel connections between systems

Figure 2 also shows a Fibre Channel connection between two systems. However, in this example, two switches are used and each system is connected to each switch.

Figure 2. Fibre Channel connections using switches between the systems
Connect the remaining host ports on the Lenovo Storage V series system to the host server ports.

Software configuration

On the Lenovo V series family system, enter the following command to get the worldwide port name (WWPN) of the FC port on the Lenovo Storage V series system.
```
svcinfo lsfcportcandidate
```
On the Lenovo V series family system, define a new host by using the WWPNs that were detected from the Lenovo Storage V series system in step 4.
Enter the following command, where wwpn_list is a colon-separated list of WWPNs of the FC ports on the Lenovo Storage V series system. If you are using the management GUI, set the Host type (operating system) to Generic.
```
svctask mkhost -fcwwpnwwpn_list
```
On the Lenovo V series family system, map the logical drives to the newly created host as a logical unit.
- To select and map several drives at one time, use the management GUI.
- To map an individual drive, enter the following command.
```
svctask mkvdiskhostmap -hosthostnamediskname
```
  hostname
  
  Name or ID of the host created in step 5
  
  diskname
  
  Name or ID of the volume that you want to migrate to the Lenovo Storage V series system
On the Lenovo Storage V series system, complete the following steps to manage the logical unit.
1. To create one empty storage pool, enter the following command.
```
svctask mkmdiskgrp -extextent_size
```
  The logical unit that is mapped from the Lenovo V series family system appears as an unmanaged-mode MDisk to the Lenovo Storage V series system.
2. To list the unmanaged-mode MDisks, enter the following command.
```
svcinfo lsmdisk
```
3. If the new unmanaged-mode MDisk is not listed, perform a fabric-level discovery.
  Enter the following command to scan the network for the unmanaged-mode MDisks.
```
svctask detectmdisk
```
4. To convert the unmanaged-mode MDisk to an image mode volume disk, enter the following command.
```
svctask mkvdisk -vtype image -iogrpiogrp_name-mdiskgrp -mdiskmdiskgrp_namemdisk_name-mirrorwritepriority redundancy
```
  iogrp_name
  
  Name or ID of the I/O group.
  
  mdiskgrp_name
  
  Name or ID of the storage pool that you created in step 7.a.
  
  mdisk_name
  
  Name or ID of the unmanaged-mode MDisk.
5. To list the WWPN of hosts that were previously using the data that the MDisk now contains, enter the following command.
```
svcinfo lsfcportcandidate
```
6. If the host does not exist on the system, enter the following command, where wwpn_list is the colon-separated list of the WWPNs of the FC ports on the host server.
```
svctask mkhost -fcwwpnwwpn_list
```
7. Map the new volume to the hosts.
  Enter the following command to create a new mapping between a volume and a host. The image mode volume becomes accessible for I/O operations to the host.
```
svctask mkvdiskhostmap -hosthostname diskname
```
  hostname
  
  Name or ID of the host you created in step 7.f.
  
  diskname
  
  Name or ID of the virtual disk you created in step 7.d.
On the host server, you can detect the new volume that is presented from the Lenovo Storage V series system and start I/O operations towards it.
If you have more than one logical drive to migrate, repeat steps 6 through 8.
On the Lenovo Storage V series system, complete the following steps to start migration for each image-mode volume. For more information about migrating data to volumes, see Managing volumes.
1. To create one empty internal storage pool, enter the following command.
```
svctask mkmdiskgrp -extextent_size
```
2. To create arrays with internal drives and add them to the internal storage pool, enter the following command.
```
svctask mkarray -levelraidtype-drivedrivelist mdiskgrpname
```
  raidtype
  
  Type of RAID array to be created.
  
  drivelist
  
  List of drive IDs.
  
  mdiskgrpname
  
  Name or ID of storage pool created in step 7.d.
3. After you determine the volume that you want to migrate and the new storage pool that you want to migrate it to, enter the following command.
```
svctask addvdiskcopy -mdiskgrpnewmdiskgrname vdiskname
```
  The copy ID of the new copy is returned. The copies are now synchronized such that the data is stored in both storage pools.
4. To check the progress of the synchronization, enter the following command.
```
svcinfo lsvdisksyncprogress
```
5. After the volume reports that it is fully synchronized and you are ready to stop using the external storage system, enter the following command on the image-mode copy of the volume.
```
svctask rmvdiskcopy
```
  The image-mode copy is deleted, and its associated MDisk becomes unmanaged.

The data on the logical drives from the Lenovo V series family system is migrated to the Lenovo Storage V series system. Host I/O is also switched to the Lenovo Storage V series system.

You can now disconnect the cabling between the switches (if applicable), the Lenovo V series family system, and the Lenovo Storage V series system.