Rekeying an encryption-enabled system using a USB flash drive

Rekeying is the process of creating a new key for the system. To create a new key, encryption must be enabled on the system; however, the rekey operation works whether or not there are encrypted arrays. Encryption is supported on Lenovo Storage V5030 models only. If you have configured encryption with USB flash drives, you can create new keys and store them on USB flash drives.

Before creating a new key, ensure that at least one USB port contains a USB flash drive that contains the current key. During the rekey process, a new key is generated and copied to the USB flash drives. The new key is then used instead of the current key. The rekey operation fails unless at least one USB flash drive contains the current key. To rekey the system you need at least three USB flash drives to store the copied key material.

Using the management GUI

Before rekeying the system, ensure that the encryption key is accessible by verifying that at least one of the USB flash drives contains the current key. Insert the other USB flash drives into the remaining ports on the rear panel of the control enclosure. Available ports are displayed to indicate which ports need USB flash drives.

To rekey the system in the management GUI, complete these steps:

In the management GUI, select Settings > Security > Encryption.
Expand USB Flash Drives to display all the detected USB flash drives on the system and select Rekey.
When the system detects the required number of the USB flash drives with at least one drive that contains an existing key, the new key is generated and copied to the USB flash drives. Click Commit after the key is created to complete the rekey operation. If errors occur during the rekey process, status messages display problems with the copy or creation of a new key. For example, if the minimum number of USB drives are inserted but none of them have an existing encryption key, the rekey operation fails. To determine and fix other possible errors, select Monitoring > Events.

Using the command-line interface

To rekey the system in the command-line interface, complete these steps:

Verify that encryption is enabled on the system by entering this command:
```
lsencryption
```
Ensure that the status indicates that the encryption is enabled. Encryption is supported on Lenovo Storage V3700 V2 XP and Lenovo Storage V5030 models only.
After verifying that encryption is enabled, you need to prepare the system to rekey the encryption keys that are currently being used on the system. Ensure that at least one of the USB flash drives that contain the current key is inserted into the configuration node. The current key is necessary; otherwise, the rekey process fails. Insert other USB flash drives into the remaining USB ports on the rear of the system. To prepare the rekey operation and copy the new key to all inserted USB flash drives on the system, enter the following command:
```
chencryption -usb newkey -key prepare
```
This command confirms at least one of the USB flash drives contain the current encryption key. It also generates a new encryption key for the system and copies the key to all USB flash drives that are inserted into the system. Optionally, you can make additional copies of the encryption keys for backups if the USB flash drives are lost or damaged.
To verify that the system is prepared and the keys are copied to the other USB flash drives, enter the following command:
```
lsencryption
```
Check that the usb_rekey parameter has the value prepared.
Note: The prepared value indicates that the new key is ready to be committed.
If USB flash drives are already inserted into the canisters, the encryption key is copied automatically. If USB flash drives are not present in the canister, insert them to begin copying the key to the drives. To verify that copies to the USB flash drive are successful, enter lsencryption to check the value in the usb_key_copies. Each successful copy to a USB flash drive increments this value. This value must match the number of USB flash drives that you inserted into the system to create the new encryption keys. Before the keys can be committed, this value must be greater than the minimum required amount.
To commit the key, enter the following command:
```
chencryption -usb newkey -key commit
```
This command makes the prepared key the current key and stores the key values on the USB flash drives.
Verify that the new key is committed by entering the following command:
```
lsencryption
```
Ensure that the value in the usb_rekey parameter is no and the usb_key_copies has the minimum required number of USB flash drives with copies of the keys. The system needs at least three USB flash drives, each with one copy of the key. It is recommended that additional copies of the keys are made and stored securely.