Procedure: Identifying which enclosure or canister to service

Use this procedure to identify which Lenovo Storage V series enclosure or canister must be serviced.

To prevent loss of access to data or loss of data when you service your system, it is important to be able to identify the correct enclosure or canister when you complete a service action. Each enclosure is identified by its model type and serial number. Model type and serial number are indicated by labels on the enclosure front and rear.

Each canister is identified by its enclosure and slot location. Viewing an enclosure from the rear, slot 1 is on the left and slot 2 is on the right. There are physical differences between Lenovo Storage V series control enclosures and expansion enclosures.

Looking at the front of a rack:

The type of the enclosure, either Control or Expansion, is labeled on the left bezel.
The model type and serial number of the enclosure are found at the bottom of the left bezel.

Lenovo Storage V series refers to the newer generation of enclosures that are listed in the following tables.

Table 1. Lenovo Storage V series control enclosures
Lenovo Storage V series Model	Machine type / model	Part Number	Warranty	Description
Lenovo Storage V3700 V2	6535-HC1	6535C1D	3 years	12-slot control enclosure for 3.5-inch drives
Lenovo Storage V3700 V2	6535-HC4	6535C2D	3 years	24-slot control enclosure for 2.5-inch drives
Lenovo Storage V3700 V2 XP	6535-HC2	6535C3D	3 years	12-slot control enclosure for 3.5-inch drives
Lenovo Storage V3700 V2 XP	6535-HC5	6535C4D	3 years	24-slot control enclosure for 2.5-inch drives
Lenovo Storage V5030	6536-HC3	6536C12	3 years	12-slot control enclosure for 3.5-inch drives
	6536-HC6	6536C22	3 years	24-slot control enclosure for 2.5-inch drives
	6536-HC3	6536C32	5 years^*	12-slot control enclosure for 3.5-inch drives
	6536-HC6	6536C42	5 years^*	24-slot control enclosure for 2.5-inch drives
Lenovo Storage V5030F	6536-HC6	6536B1F	3 years	24-slot control enclosure for 2.5-inch flash drives
Lenovo Storage V5030F	6536-HC6	6536B2F	5 years^*	24-slot control enclosure for 2.5-inch flash drives

Note: ^* means the warranty year is optional and requires extra pay.

Table 2. Lenovo Storage V series expansion enclosures
Lenovo Storage V series Model	Machine type / model	Part Number	Warranty	Description
Lenovo Storage V3700 V2 and Lenovo Storage V3700 V2 XP	6535-HC7	6535N1F	3 years	12-slot expansion enclosure for 3.5-inch drives
Lenovo Storage V3700 V2 and Lenovo Storage V3700 V2 XP	6535-HC8	6535N2F	3 years	24-slot expansion enclosure for 2.5-inch drives
Lenovo Storage V5030	6536-HC7	6536N13	3 years	12-slot expansion enclosure for 3.5-inch drives
	6536-HC8	6536N23	3 years	24-slot expansion enclosure for 2.5-inch drives
	6536-HC7	6536N33	5 years^*	12-slot expansion enclosure for 3.5-inch drives
	6536-HC8	6536N43	5 years^*	24-slot expansion enclosure for 2.5-inch drives
Lenovo Storage V5030F	6536-HC8	6536B3F	3 years	24-slot expansion enclosure for 2.5-inch flash drives
Lenovo Storage V5030F	6536-HC8	6536B4F	5 years^*	24-slot expansion enclosure for 2.5-inch flash drives

Note: ^* means the warranty year is optional and requires extra pay.

Looking at the rear of a rack:

Control enclosures contain tall and narrow power supplies at the far left and right of the enclosure, with the node canisters installed in between, side by side.
Expansion enclosures contain short node canisters installed side by side, above short power supply units also installed side by side.
Control enclosures contain node canisters that have Ethernet ports, and USB ports. Expansion enclosures do not have any of these ports. The model type is shown on a label.
Each canister is identified by its slot location. Viewing an enclosure from the rear, slot 1 is on the left and slot 2 is on the right.

A canister is uniquely identified by the enclosure that it is in and its slot location. This ID is shown as E-C or E|C where E is the enclosure ID and C is the canister location. On the service assistant, the ID is known as the Panel.

Notes:

When a node canister is added to a clustered system as a node, it is given a node name and a node ID. The default node name is nodeN, where N is the node ID. The node ID does not represent the slot location of the node. On the Monitoring > System page use the dynamic graphic to show the back of the system. Hover over the canister to display the node name and canister location. The service assistant home page also shows both the node name and the canister location. If you have only the node name, use these panels to determine the node canister location.
It is good practice to use this procedure to identify which enclosure or canister must be serviced, as completing a service action on the wrong canister can lead to loss of access to data or loss of data.

To control the identify LED of an enclosure or online canister, use the management GUI:

Log in to the management GUI for the system.
Select the Monitoring > System panel.
Select the canister or enclosure to be identified.
Select Action > Identify to control the identify LEDs for the component.

Alternatively, if a node canister is not online to the system, use the service assistant to control the identify LED.

Log in to the service assistant of the node canister to be identified.
Click Identify at the upper left of the page to control the identify LEDs.