SATA optical drives (optional for 2.5-inch models):
DVD-ROM
Multi-burner
Hard disk drive expansion bays (depending on the model):
2.5-inch models: Up to eight 2.5-inch hot-swap SAS/SATA hard disk drive bays (with an optional optical drive bay)
3.5-inch models: Up to three 3.5-inch hot-swap SAS/SATA or simple-swap SATA hard disk drive bays
Attention
As a general consideration, do not mix standard 512-byte and advanced 4-KB format drives in the same RAID array because it may lead to potential performance issues.
The maximum video resolution is 1600 x 1200 at 75 Hz.
SVGA compatible video controller
DDR3 528 MHz SDRAM video memory controller
Avocent Digital Video Compression
16 MB of video memory (not expandable)
Hot-swap fans:
One microprocessor: 4 dual-motor hot-swap fans.
Two microprocessors: 6 dual-motor hot-swap fans.
Power supply:
Up to two hot-swap power supplies for redundancy support
550-watt ac
750-watt ac
750-watt dc
Note
Power supplies in the server must be with the same power rating or wattage.
Integrated functions:
Integrated Management Module II (IMM2), which consolidates multiple management functions in a single chip.
Intel I350AM4 Quad Port Gigabit Ethernet controller with Wake on LAN support
Eight Universal Serial Bus (USB) ports for 3.5-inch models. Seven Universal Serial Bus (USB) ports for 2.5-inch models. One port is for optional USB flash device with embedded hypervisor software is installed.
Six network ports (four 1 Gb Ethernet ports on the system board and two additional ports when the optional Dual-Port 10 Gb Network Adapter is installed)
One System Management 1 Gb Ethernet port on the rear connected to a systems management network. This system management connector is dedicated to the IMM2 functions.
One serial port
RAID controllers (depending on the model):
A ServeRAID H1110 SAS/SATA adapter that provides RAID 0, 1, and 10.
A ServeRAID M1115 SAS/SATA adapter that provides RAID 0, 1, and 10 with optional FoD RAID 5/50 and SED (Self Encrypting Drive) upgrade.
A ServeRAID M5110 SAS/SATA adapter that provides RAID 0, 1, and 10. Optional upgrade:
RAID 5/50 (512 MB Cache) with optional FoD RAID 6/60 and SED upgrade
RAID 5/50 (512 MB Flash) with optional FoD RAID 6/60 and SED upgrade
RAID 5/50 (1 GB Flash) with optional FoD RAID 6/60 and SED upgrade
RAID 5/50 and SED (Zero Cache)
A ServeRAID M5120 SAS/SATA adapter that provides RAID 0, 1, and 10. Optional upgrade:
RAID 5/50 (512 MB Cache) with optional FoD RAID 6/60 and SED upgrade
RAID 5/50 (512 MB Flash) with optional FoD RAID 6/60 and SED upgrade
RAID 5/50 (1 GB Flash) with optional FoD RAID 6/60 and SED upgrade
RAID 5/50 and SED (Zero Cache)
Environment: compliant with ASHRAE class A3 specifications.
Server on:
Temperature:
5°C to 40°C (41°F to 104°F)
Altitude: 0 to 950 m (3,117 ft); decrease the maximum system temperature by 1°C for every 175-m increase in altitude.
Maximum altitude: 3,050 m (10,000 ft), 5°C to 28°C (41°F to 82.4°F)
Humidity:
Non-condensing: -12°C dew point (10.4°F)
Relative humidity: 8% to 85%
Maximum dew point: 24°C (75.2°F)
Maximum rate of temperature change:
Tape drives: 5°C/hr (41°F/hr)
Hard disk drives: 20°C/hr (68°F/hr)
Server off:
Temperature: 5°C to 45°C (41°F to 113°F)
Relative humidity: 8% to 85%
Maximum dew point: 27°C (80.6°F)
Storage (non-operating):
Temperature: 1°C to 60°C (33.8°F to 140°F)
Maximum altitude: 3,050 m (10,000 ft)
Relative humidity: 5% to 80%
Maximum dew point: 29°C (84.2°F)
Shipment (non-operating):
Temperature: -40°C to 60°C (-40°F to 140°F)
Maximum altitude: 10,700 m (35,105 ft)
Relative humidity: 5% to 100%
Maximum dew point: 29°C (84.2°F)
Particulate contamination: airborne particulates and reactive gases acting alone or in combination with other environmental factors such as humidity or temperature might pose a risk to the server. For information about the limits for particulates and gases, see Particulate contamination.
Attention
Design to ASHRAE Class A3, ambient of 40°C, with relaxed support:
Support cloud like workload with no performance degradation acceptable (Turbo-Off)
Under no circumstance, can any combination of worst case workload and configuration result in system shutdown or design exposure at 40°C
Specific microprocessors supported environment:
Microprocessor Intel Xeon E5-2690, 135W:
Temperature: 10°C to 27°C (50°F to 80.6°F)
Altitude: 0 to 304.8 m (1,000 ft)
Microprocessor models with 115W and 130W:
Temperature: 10°C to 35°C (50°F to 95°F)
Altitude: 0 to 914.4 m (3,000 ft)
Size:
1U
Height: 43 mm (1.7 inches)
Depth: 734 mm (28.9 inches)
Width: 429 mm (16.9 inches)
Weight: approximately 16.4 kg (36.16 lb) when fully configured
Acoustical noise emissions:
Sound power, idling: 6.5 bels maximum
Sound power, operating: 6.5 bels maximum
Heat output:
Approximate heat output:
Minimum configuration: 461 Btu per hour (AC 135 watts)
Maximum configuration: 3378 Btu per hour (AC 990 watts)
Electrical input:
Sine-wave input (50 - 60 Hz) required
Input voltage low range:
Minimum: 100 V ac
Maximum: 127 V ac
Input voltage high range:
Minimum: 200 V ac
Maximum: 240 V ac
Input kilovolt-amperes (kVA), approximately:
Minimum: 0.14 kVA
Maximum: 0.993 kVA
Note
Power consumption and heat output vary depending on the number and type of optional features installed and the power-management optional features in use.
The noise emission level stated is the declared (upper limit) sound power level, in bels, for a random sample of machines. All measurements are made in accordance with ISO 7779 and reported in conformance with ISO 9296. Actual sound-pressure levels in a given location might exceed the average values stated because of room reflections and other nearby noise sources. The noise emission level stated in the declared (upper limit) sound-power level, in bels, for a random sample of system.
Total harmonic distortion of the electricity supply system:
The maximum harmonic content of the input voltage waveform will be equal or less than 2%. The qualification is compliant with EN 61000-3-2.
Information and documentation on the instrumentation set-up and circuits used for electrical testing:
ENERGY STAR Test Method for Computer Servers; ECOVA Generalized Test Protocol for Calculating the Energy Efficiency of Internal Ac-Dc and Dc-Dc Power Supplies.
Measurement methodology used to determine information in this document:
ENERGY STAR Servers Version 2.0 Program Requirements; ECOVA Generalized Test Protocol for Calculating the Energy Efficiency of Internal Ac-Dc and Dc-Dc Power Supplies.