lsservicestatus

Use the lsservicestatus command to display the status of a node.

Syntax

sainfo lsservicestatus [panel_name]

Parameters

panel_name
(Optional) If a panel_name is provided, the service recommendation for the local node is returned. If a panel_name from the list that is returned by lsservicenodes is specified, then the service recommendation for that node is returned. The command fails if the panel_name ID is not in the list that is returned by lsservicenodes. This output is returned as the node status on all Universal Serial Bus (USB) flash drive commands.

Description

Use this command to display the status of a node. This command provides all the information that can be obtained by using the front panel of asystem node.

You can run this command on any node, even one that is not part of a clustered system (system), to obtain the vital product data (VPD) and error status.

lsservicestatus output shows possible outputs.
Note: On a node that is not part of a system, some of the fields are blank or N/A.
Table 1. lsservicestatus output
Attribute Value
console_ip Indicates an Internet Protocol (IP) Version 4 or 6 address.
Note: This field might be blank if the node is not present in a system.
has_nas_key Indicates the has_nas_key field value. The values are yes or no.
Note: This field might be blank if the node is not present in a system.
fc_io_ports Indicates the number of configured Fibre Channel (FC) input/output (I/O) ports on the node. The value is an alphanumeric from 0 to N. This field is repeated for each management address.
fc_io_port_id Indicates the ID of the FC I/O port. The value is a number. This field is repeated for each management address.
fc_io_port_WWPN Indicates the Worldwide port name (WWPN) of the FC I/O port. The value is 16 hexadecimal characters (lower case). This field is repeated for each management address.
fc_io_port_switch_WWPN Indicates the WWPN of the fabric port name. The value is 16 hexadecimal characters (lower case) or all zeroes if never active. This field is repeated for each management address.
fc_io_port_state Indicates whether the port is working - active or inactive. This field is repeated for each management address.
fc_io_port_FCF_MAC Indicates the FCF MAC address for active Ethernet. The value is blank for inactive or broken Ethernet, or N/A for FC type. This field is repeated for each management address.
fc_io_port_vlanid Indicates the virtual local area network (VLAN) ID being used. The value is three hexadecimal digits for previously active or inactive Ethernet, blank for Ethernet that is never active, or N/A for FC type. This field is repeated for each management address.
fc_io_port_type Indicates the type of the platform port for the FC I/O port. This field is repeated for each management address.
fc_io_port_type_port_id Indicates the platform port type index of the platform port supplies the FC I/O port. Use both fc_io_port_type_port_id and fc_io_port_type to find the platform port. This field is repeated for each management address.
panel_name Indicates the front panel name, enclosure IDs, or canister IDs that identify the node.
cluster_id Indicates the ID of a clustered system.
cluster_name Indicates the name of a system. When you use this parameter, the detailed view of the specific system is displayed and any value that you specified by the -filtervalueparameter is ignored. If you do not specify the cluster_name parameter, the concise view of all systems that match the filtering requirements that are specified by the -filtervalue parameter are displayed.
cluster_status Indicates that the error code is the same as the one displayed on the front panel.
cluster_ip_count Indicates the maximum number of management addresses you can configure.
cluster_ip_port Indicates the system IP port. This field is repeated for each management address.
cluster_ip Indicates the Internet Protocol Version 4 (IPv4) management IP address. This field is repeated for each management address.
cluster_gw Indicates the IPv4 management IP gateway. This field is repeated for each management address.
cluster_mask Indicates the IPv4 management IP mask. This field is repeated for each management address.
cluster_ip_6 Indicates the Internet Protocol Version 6 (IPv6) management IP address. This field is repeated for each management address.
cluster_gw_6 Indicates the IPv6 management IP gateway. This field is repeated for each management address.
cluster_prefix_6 Indicates the IPv6 management IP prefix. This field is repeated for each management address.
node_id Indicates the ID of the node that is being configured. The value is a number.
node_name Indicates the name of the node that is being configured.
node_status Indicates the node status. The values are:
  • active indicates that the node is part of a system and can perform I/O.
  • service indicates that the node is in service mode, standby mode, or node rescue mode.
  • candidate indicates that the node is not part of a system
  • starting indicates that the node is part of a system and is attempting to join the system.
  • spare indicates that the node is a spare node.
config_node Indicates whether it is a configuration node. The values are yes or no
hardware Indicates the hardware type: The values are:
  • DH8
  • DH8
service_IP_address Indicates the IPv4 service address for the node.
service_gateway Indicates the IPv4 service gateway for the node.
service_subnet_mask Indicates the IPv4 service mask for the node.
service_IP_address_6 Indicates the IPv6 service address for the node.
service_gateway_6 Indicates the IPv6 service gateway for the node.
service_prefix_6 Indicates the IPv6 service prefix for the node.
node_sw_version Indicates the version of system code for the node.
node_sw_build Indicates the build string for code on the node.
cluster_sw_build Indicates the CSM build that the system is running.
node_error_count Indicates the number of node errors.
node_error_data Indicates the type of node errors.
FC_port_count Indicates the number of FC ports. This field is repeated for each management address.
FC_port_id Indicates the port ID. This field is repeated for each management address.
port_status Indicates the port status. This value must match the port on the front panel, enclosure, or canister.
port_speed Indicates the port speed. This value must match the port speed on the front panel, enclosure, or canister.
port_WWPN Indicates the worldwide port number of the port.
SFP_type Indicates the SFP type. The values are long-wave or short-wave.
ethernet_port_count Indicates the number of detected Ethernet ports.
ethernet_port_id Indicates the ID of an Ethernet port.
port_status Indicates the port status. The values are:
  • online
  • offline
  • not configured
online | offline | not configured
port_speed Indicates the port speed. The values are:
  • 10Mbps
  • 100Mbps
  • 1Gbps
  • 10Gbps
  • full
  • half
MAC Indicates a single MAC address.
vnport_count Indicates the number of VN ports that are created on top of each physical Fibre Channel over Ethernet (FCoE) port.
vnport_id Indicates the VN port ID.
vnport_wwpn Indicates the WWPN assigned to the VN port.
vnport_FCF_mac Indicates the MAC address for the FCF to which the VN port is connected.
vnport_vlanid Indicates the VLAN ID used by the VN port. The value is blank for FC ports.
product_mtm Indicates the machine type and model.
product_serial Indicates the node serial number.
node_WWNN Indicates the last active WWNN stored in the node; blank if no system data.
enclosure_WWNN_1 Indicates the first canister WWNN from the enclosure VPD.
enclosure_WWNN_2 Indicates the second canister WWNN from the enclosure VPD.
node_part_identity Indicates the 11S string from the hardware VPD.
node_FRU_part Indicates the node field-replaceable unit (FRU) part number, if stored in node VPD
enclosure_part_identity Indicates the S11 data.
PSU_count Indicates the number of expected PSUs (two).
PSU_id Indicates the ID of the slot the PSU is in. The value is a number.
PSU_status Indicates the PSU status. The status is missing, failed, or active.
time_to_charge Indicates the estimated start time (in minutes) needed for 50% of the battery to be charged.
Battery_charging Indicates the percentage of charge of the batteries.
Battery_count Indicates the number of expected batteries (two).
Battery_id Indicates the ID of the slot the battery is in.
Battery_status Indicates that the status is missing, failed, charging, or active.
Battery_FRU_part Indicates the FRU part number of the battery.
Battery_part_identity Indicates the 11S FRU identity of the battery (includes the serial number).
Battery_fault_led Indicates thee fault light-emitting diode (LED) status.
Battery_charging_status Indicates the battery charge status.
Battery_cycle_count Indicates the number of charge or discharge cycles that are performed by the battery.
Battery_powered_on_hours Indicates the number of hours the battery is in a powered node.
Battery_last_recondition Indicates the system timestamp of the last successful gas gauge calibration.
Battery_midplane_FRU_part Indicates the FRU part number of the battery midplane
Battery_midplane_part_identity Indicates the 11S FRU identity of the battery midplane (which includes the serial number).
Battery_midplane_FW_version Indicates the firmware version that is running on the battery midplane.
Battery_power_cable_FRU_part Indicates the FRU part number of the battery power cable.
Battery_power_sense_cable_FRU_part Indicates the FRU part number of the battery midplane power sense cable.
Battery_comms_cable_FRU_part Indicates the FRU part number of the battery midplane communication cable.
Battery_EPOW_cable_FRU_part Indicates the FRU part number of the battery midplane EPOW cable.
node_location_copy Indicates the node location copy status. This value is equivalent to the panel name and is blank if a node is removed from a system.
node_product_mtm_copy Indicates the node product machine type copy status. This value is equivalent to panel product_mtm; blank if a node is removed from a system.
node_product_serial_copy Indicates the node product serial copy status. This value is equivalent to product_serial; blank if a node is removed from a system.
node_WWNN_1_copy Indicates the node WWNN first copy status. This value is equivalent to enclosure_WWNN_1; blank if a node is removed from a system.
node_WWNN_2_copy Indicates the node WWNN second copy status. This value is equivalent to enclosure_WWNN_2; blank if a node is removed from a system.
latest_cluster_id Indicates the system ID running on the current enclosure; blank if a node is removed from a system.
latest_cluster_id Indicates the system ID running on the current enclosure; blank if a node is removed from a system.
techport Indicates the technician port (for emergency node maintenance):
  • permanent indicates a dedicated technician port
  • enabled indicates an enabled technician port
  • disabled indicates a disabled technician port
  • none indicates that there is no technician port

An invocation example

sainfo lsservicestatus

The resulting output:

panel_name 150434
cluster_id 000002006ee1445e
cluster_name Cluster_192.168.8.241
cluster_status Active
cluster_ip_count 2
cluster_port 1
cluster_ip 192.168.8.241
cluster_gw 192.168.8.1
cluster_mask 255.255.255.0
cluster_ip_6
cluster_gw_6
cluster_prefix_6
cluster_port 2
cluster_ip
cluster_gw
cluster_mask
cluster_ip_6
cluster_gw_6
cluster_prefix_6
node_id 1
node_name node1
node_status Active
config_node Yes
hardware DH8
service_IP_address
service_gateway
service_subnet_mask
service_IP_address_6
service_gateway_6
service_prefix_6
service_IP_mode dhcpfallback
node_sw_version 6.4.0.0
node_sw_build 64.8.1205180000
cluster_sw_build 64.8.1205180000
node_error_count 0
fc_ports 4
port_id 1
port_status Active
port_speed 8Gb
port_WWPN 500507680140a22f
SFP_type Short-wave
port_id 2
port_status Active
port_speed 8Gb
port_WWPN 500507680130a22f
SFP_type Short-wave
port_id 3
port_status Active
port_speed 8Gb
port_WWPN 500507680110a22f
SFP_type Short-wave
port_id 4
port_status Active
port_speed 8Gb
port_WWPN 500507680120a22f
SFP_type Short-wave
ethernet_ports 4
ethernet_port_id 1
port_status Link Online
port_speed 1Gb/s - Full
MAC 00:21:5e:db:30:38
vnport_count 0
ethernet_port_id 2
port_status Not Configured
port_speed
MAC 00:21:5e:db:30:3a
vnport_count 0
ethernet_port_id 3
port_status Not Configured
port_speed 10Gb/s - Full
MAC 00:00:c9:bc:6f:22
vnport_count 0
ethernet_port_id 4
port_status Not Configured
port_speed 10Gb/s - Full
MAC 00:00:c9:bc:6f:20
vnport_count 0
product_mtm 2145-DH8
product_serial 75HAXYA
time_to_charge 0
Battery_charging 0
Battery_count 2
Battery_id 1
Battery_status active
Battery_FRU_part 12Z9876
Battery_part_identity 11S98Z1234YM11BG123456
Battery_fault_led OFF
Battery_charging_Status charged
Battery_cycle_count 5
Battery_powered_on_hours 12345
Battery_last_recondition 130629123456
Battery_id 2
Battery_status failed
Battery_FRU_part 12Z9876
Battery_part_identity 11S98Z1234YM11BG234567
Battery_fault_led ON
Battery_charging_Status charged
Battery_cycle_count 5
Battery_power_on_hours 12345
Battery_last_recondition 130702123400
Battery_midplane_FRU_part 12Z9880
Battery_power_cable_FRU_part 12Z9881
Battery_power_sense_cable_FRU_part 12Z9882
Battery_comms_cable_FRU_part 12Z9883
Battery_EPOW_cable_FRU_part 12Z9884

dump_name 150434
node_WWNN 500507680100a22f
disk_WWNN_suffix 0A22F
panel_WWNN_suffix 0A22F
UPS_serial_number
UPS_status
enclosure_WWNN_1
enclosure_WWNN_2
node_part_identity
node_FRU_part
enclosure_identity
PSU_count
PSU_id
PSU_status
PSU_id
PSU_status

node_location_copy
node_product_mtm_copy
node_product_serial_copy
node_WWNN_1_copy
node_WWNN_2_copy
latest_cluster_id
next_cluster_id
console_IP 192.168.8.241:443
has_nas_key no
fc_io_ports 6
fc_io_port_id 1
fc_io_port_WWPN 500507680140a22f
fc_io_port_switch_WWPN 200000051e630f9a
fc_io_port_state Active
fc_io_port_FCF_MAC N/A
fc_io_port_vlanid N/A
fc_io_port_type FC
fc_io_port_type_port_id 1
fc_io_port_id 2
fc_io_port_WWPN 500507680130a22f
fc_io_port_switch_WWPN 200400051e630f9a
fc_io_port_state Active
fc_io_port_FCF_MAC N/A
fc_io_port_vlanid N/A
fc_io_port_type FC
fc_io_port_type_port_id 2
fc_io_port_id 3
fc_io_port_WWPN 500507680110a22f
fc_io_port_switch_WWPN 200000051e7ded49
fc_io_port_state Active
fc_io_port_FCF_MAC N/A
fc_io_port_vlanid N/A
fc_io_port_type FC
fc_io_port_type_port_id 3
fc_io_port_id 4
fc_io_port_WWPN 500507680120a22f
fc_io_port_switch_WWPN 200400051e7ded49
fc_io_port_state Active
fc_io_port_FCF_MAC N/A
fc_io_port_vlanid N/A
fc_io_port_type FC
fc_io_port_type_port_id 4
fc_io_port_id 5
fc_io_port_WWPN 500507680150a22f
fc_io_port_switch_WWPN 2064000573cd6201
fc_io_port_state Active
fc_io_port_FCF_MAC 00:05:73:CD:62:00
fc_io_port_vlanid 100
fc_io_port_type Ethernet
fc_io_port_type_port_id 3
fc_io_port_id 6
fc_io_port_WWPN 500507680160a22f
fc_io_port_switch_WWPN 2064000573c8a701
fc_io_port_state Active
fc_io_port_FCF_MAC 00:05:73:C8:A7:00
fc_io_port_vlanid 100
fc_io_port_type Ethernet
fc_io_port_type_port_id 4
service_IP_mode
service_IP_mode_6
machine_part_number 2072S2C
node_machine_part_number_copy 2072L2C
local_fc_port_mask:0000000000000000000000000000000000000000000000000000000000001101
partner_fc_port_mask:0000000000000000000000000000000000000000000000000000000000000011password_reset_enabled yesidentify_LED offproduct_name Compustrongtechport on